Preskoči na glavno vsebino
  • Domov
  • Izdelki
  • XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo
XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo

XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo

Uporabite XPS 700 tam, kjer je ključna maksimalna tlačna trdnost – vključno s težko civilno infrastrukturo, industrijskimi temelji in visokoobremenjeno cestno gradnjo.

Tlačna trdnost, kPa:
700
Deklarirana toplotna prevodnost λD, W/(m·K):
0,034–0,035
Razred reakcije na ogenj:
E
Dimenzije plošče (dolžina × širina), mm:
1250 × 600
Nazivna debelina, mm:
20–150
Vrsta površine:
Gladko
Vrsta roba:
Ravni rob (I) / L-oblikovni rob (L)
Standard proizvoda:
EN 13164:2012+A1:2015

Težka toga plošča iz ekstrudiranega polistirena, razvita za toplotno izolacijo konstrukcij, ki so izpostavljene izjemnim mehanskim obremenitvam in zahtevnim aplikacijam v gradbeništvu. Na voljo v debelinah od 20 mm do 150 mm, PNP XPS 700 zagotavlja dosledno nizko toplotno prevodnost in izjemno tlačno trdnost ≥ 700 kPa.

Opis

PNP XPS 700 je visokozmogljiv toplotnoizolacijski material (najnovejša generacija XPS), izdelan iz splošnonamenskega polistirena. Odlikuje ga gladka površina in homogena struktura zaprtih celic z deklarirano toplotno prevodnostjo (λD) 0,034 W/m·K za debeline 20–100 mm in 0,035 W/m·K za debeline 120–150 mm. Tlačna trdnost ustreza CS(10\Y) 700 (≥ 700 kPa), dolgotrajna vpojnost vode pri popolni potopitvi pa je razvrščena kot WL(T) 0,7 (≤ 0,7 vol.-%). Plošče so skladne s standardom EN 13164:2012+A1:2015 in uredbo REACH ter ne vsebujejo HBCDD ali drugih snovi, ki vzbujajo resne skrbi.

Področja uporabe

  • Toplotna izolacija cestnih in gradbenih konstrukcij
  • Močno obremenjene talne plošče, temeljne plošče in industrijske površine
  • Mostovne plošče in infrastrukturni elementi, izpostavljeni visokim prometnim obremenitvam
  • Toplotna izolacija tal v hladilnicah in zamrzovalnih prostorih
  • Izolacija temeljev in podlage pri izjemnih obremenitvah

Prednosti

  • Izjemno visoka tlačna trdnost — CS(10\Y) ≥ 700 kPa, zasnovana za konstrukcije z ekstremnimi obremenitvami
  • Dosledno nizka toplotna prevodnost (λD 0,034–0,035 W/m·K)
  • Skoraj ničelna vpojnost vode — homogena struktura zaprtih neodvisnih celic (WL(T) ≤ 0,7 vol.-%)
  • Popolna biostabilnost in dokazana dolgotrajna vzdržljivost
  • Široko delovno temperaturno območje: −70 °C do +75 °C
  • Skladnost z uredbo REACH in okoljska odgovornost — pri proizvodnji niso uporabljeni pogonski plini, ki uničujejo ozonski plašč
XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo — Tehnično
NepremičninaDebelina / stanjeDeklarirana vrednost
Tlačna trdnost / tlačna napetost pri 10 % deformaciji, CS(10\Y)CS(10\Y)700 (≥700 kPa)
Razred reakcije na ogenjE
Deklarirana toplotna prevodnost λD, W/(m·K)20–100 mm0,034
Deklarirana toplotna prevodnost λD, W/(m·K)120–150 mm0,035
Dolgotrajna absorpcija vode s popolnim potapljanjem, WL(T)WL(T)0,7 (≤ 0,7 [Vol.-%])
Dolgotrajna absorpcija vode z difuzijo, WD(V)WD(V)3 (≤3,0 [Vol-%])
Dimenzijska stabilnost pri določenih pogojih, DSDS(70,90)
Debelinska toleranca, razredT1
Tlačna leznost, CCCC(2/1,5/50)210
Natezna trdnost pravokotno na površino, TRTR 200
Odpornost proti zmrzovanju in tajanju, FTCDFTCD1 (≤1 [Vol-%])
Delovna temperatura, °C-70 … +75 °C
Vrsta površineGladko
Vrsta robaI l
Deformation under specified compressive load and temperature conditionsDLT(2)5
Standard proizvodaEN 13164:2012+A1:2015

Vrednosti so v skladu z aktualnim tehničnim listom.

XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo — Embalaža
Nazivna debelina, mmDeklarirana toplotna upornost RD, m²·K/WPlošč v paketu, kosPovršina paketa, m²Prostornina paketa, m³
200,552015,000,3000
300,85139,750,2925
401,15107,500,3000
501,4586,000,3000
601,7575,250,3150
802,3553,750,3000
1002,9043,000,3000
1203,4032,250,2700
1504,2521,500,2250

Transport dimensions for boards with L-edge: 615x1265 mm

XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo

Tehnični list

pnp_xps700_600x1250_techcard_sl (21.07.2023).pdf

PDF · SL

XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo

Izjava o lastnostih

DoP PNP XPS 700_sl.pdf

PDF · SL

XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo: is it the right board?

When to use it

  • Road and infrastructure construction on frost-susceptible or heaving soils where compressive strength of ≥ 700 kPa is specified by the designer.
  • Bridge decks and civil engineering structures subject to high or repeated traffic loads that exceed the capacity of XPS 500.
  • Heavily loaded industrial ground slabs and pavements where point loads or concentrated stresses require the highest available compressive resistance in the PNP range.
  • Cold-store and freezer-room floor insulation under reinforced concrete slabs carrying heavy racking or forklift traffic.
  • Foundation and subgrade thermal insulation under extreme permanent load conditions in civil or industrial projects.
  • Lightweight earth fill and embankment applications on soft or compressible ground where the insulation layer must carry significant overburden.
  • Any application where the structural or geotechnical engineer has specified CS(10\Y)700 or an equivalent 700 kPa compressive strength class under EN 13164.

When not to use it

  • Standard residential floor slabs and foundation slabs with moderate loads, because 700 kPa compressive strength is unnecessary and a lower-grade product is more cost-effective.
  • Facade and ETICS plaster systems, because XPS 700 has a smooth surface that does not provide the mechanical key required for reliable adhesion of renders or adhesive compounds.
  • Flat-roof and inverted-roof assemblies where drainage falls are needed, because XPS 700 is not available in factory-tapered form.
  • Applications where a waffled or milled-and-grooved surface finish is required by the bonded layer system, since XPS 700 is produced with a smooth skin only.
  • Thin thermal-bridge inserts or cavity-wall applications where the high density and cost premium of 700 kPa boards offer no performance benefit over lighter grades.

Choose instead

  • Standard residential floors, accessible roofs, and foundation slabs with normal loads — choose XPS 300 (CS(10\Y)300, ≥ 300 kPa).
  • Facade and ETICS plaster or render systems requiring adhesion surface — choose XPS 300 W (waffled, CS(10\Y)300) or XPS 150 W X-Grip (waffled, CS(10\Y)150).
  • Flat roofs and terraces where drainage falls must be created in a single layer — choose XPS 300 SLOPE (factory-tapered, CS(10\Y)300).
  • Industrial floors and heavily loaded parking decks that do not reach 700 kPa requirements — choose XPS 500 (CS(10\Y)500, ≥ 500 kPa).
  • Thin thermal-bridge inserts, cavity walls, and lightly loaded assemblies — choose XPS 150 W X-Grip or XPS 300 as appropriate to the load and surface requirement.

When do you really need 700 kPa? Understanding XPS 700 compressive strength

XPS 700 is the highest compressive-strength board in the PNP XPS range, rated CS(10\Y)700 — meaning the test showed a compressive stress of ≥ 700 kPa at 10 % deformation or yield under EN 826. This supports its use wherever the structural or geotechnical engineer calculates that the insulation layer will be subjected to extreme static or dynamic loads: road sub-bases on frost-susceptible soils, bridge deck build-ups, heavily trafficked industrial pavements, and freezer-room floors under dense racking systems.

Despite its exceptional mechanical strength, XPS 700 shares the same declared thermal conductivity as the rest of the PNP range — λD 0.034 W/(m·K) for thicknesses of 20–100 mm and 0.035 W/(m·K) for 120–150 mm — and its closed-cell structure delivers long-term water absorption of WL(T) 0.7 (≤ 0.7 Vol.-%) and freeze–thaw resistance rated FTCD1. The compressive creep class is CC(2/1.5/50)210, the highest in the PNP range, which this alone does not eliminate the need for a qualified designer to verify long-term deformation under the project's specific load combination.

XPS 700 has a smooth surface skin and is produced in thicknesses from 20 mm to 150 mm in standard format (see the current TDS for any on-request thickness options). It is not available with a waffled or milled-and-grooved surface, so it cannot substitute for XPS 300 W or XPS 150 W X-Grip in bonded facade or ETICS systems. Where loads fall within the 300–500 kPa range, XPS 300 or XPS 500 will typically be the more appropriate and economical choice. Always confirm the required compressive strength class with a structural or geotechnical engineer before specifying XPS 700.

XPS 700 — Toplotna izolacija za ekstremne obremenitve in gradbeništvo — frequently asked questions

What compressive strength does XPS 700 provide, and how is it classified?

XPS 700 is classified CS(10\Y)700 under EN 826, meaning it achieves a compressive stress of ≥ 700 kPa at 10 % deformation or yield. This is the highest compressive-strength class in the PNP XPS product range. Always have a structural or geotechnical engineer confirm whether this class is required for your specific application.

Does XPS 700 have the same thermal conductivity as lower-strength PNP boards?

Yes. XPS 700 has a declared thermal conductivity (λD) of 0.034 W/(m·K) for thicknesses of 20–100 mm and 0.035 W/(m·K) for 120–150 mm, identical to XPS 300 and XPS 500 in those thickness ranges. Higher compressive strength does not penalise thermal performance in this product.

Can XPS 700 be used under renders or adhesive-bonded facade systems?

No. XPS 700 is produced with a smooth surface skin only, which does not provide the mechanical key required for reliable adhesion of plasters, renders, or tile adhesives. For bonded facade and ETICS systems, choose XPS 300 W (waffled) or XPS 150 W X-Grip instead.

What thicknesses are available for XPS 700?

Standard packaging thicknesses are 20, 30, 40, 50, 60, 80, 100, 120, and 150 mm. For thicknesses outside this range, see the current TDS or contact PNP XPS at sales@pnpinsulation.com.

How does XPS 700 compare to XPS 500 for industrial floors?

Both products are engineered for high-load applications, but XPS 700 provides ≥ 700 kPa compressive strength versus ≥ 500 kPa for XPS 500, and its compressive creep class is CC(2/1.5/50)210 compared to CC(2/1.5/50)150 for XPS 500. XPS 700 is the appropriate choice only when the designer's load analysis requires the higher class; otherwise XPS 500 is typically sufficient and should be evaluated first.

Is XPS 700 suitable for road construction and frost protection layers?

Yes. Road construction, infrastructure on frost-susceptible or heaving soils, and bridge deck build-ups are among the primary intended applications for XPS 700. The board's CS(10\Y)700 rating, FTCD1 freeze–thaw resistance, and WL(T)0.7 long-term water absorption all support these uses; however, final specification must be confirmed by a qualified civil or geotechnical engineer in accordance with the applicable national road design standards.

What standard governs XPS 700, and is a Declaration of Performance available?

XPS 700 conforms to EN 13164:2012+A1:2015 and a Declaration of Performance (DoP) is available — see the document 'DoP PNP XPS 700_eng.pdf' (updated 2025-03-17) and the technical data sheet 'pnp_xps700_600x1250_techcard_en (21.07.2023).pdf' (updated 2025-03-17) via the PNP documentation page.

Does XPS 700 contain HBCDD or other substances of very high concern?

No. XPS 700 is REACH-compliant and contains no HBCDD or other substances of very high concern, consistent with all products in the PNP XPS range.

Oglejte si tudi

XPS 150 W X-Grip — Vrhunska toplotna izolacija z močnim oprijemom

X-Grip · 150 kPa

XPS 150 W X-Grip — Vrhunska toplotna izolacija z močnim oprijemom

Izberite XPS 150 W X-Grip za nanašanje težkih ometov, lepil za ploščice ali sistemov ETICS na stene, kletne prostore, tla ali strehe, kjer je zahtevana visoka trdnost sprijemnosti izolacije.

Več podrobnosti

XPS 300 — Toplotna izolacija temeljev in tal

Smooth · 300 kPa

XPS 300 — Toplotna izolacija temeljev in tal

Uporabite XPS 300 tam, kjer težke obremenitve zahtevajo zanesljivo toplotno izolacijo – vključno s temelji, talnimi ploščami in dostopnimi strehami.

Več podrobnosti

XPS 300 W — Visoko-adhezivna strukturna toplotna izolacija

W (Waffle) · 300 kPa

XPS 300 W — Visoko-adhezivna strukturna toplotna izolacija

Uporabite XPS 300 W na dostopnih strehah ali podestnih ploščah, kjer sta ključnega pomena nosilnost in maksimalna oprijemljivost za membrane ali premaze.

Več podrobnosti

XPS 500 — Industrijska in visokotlačna toplotna izolacija

Smooth · 500 kPa

XPS 500 — Industrijska in visokotlačna toplotna izolacija

Uporabite XPS 500 tam, kjer visoke statične in dinamične obremenitve zahtevajo maksimalno odpornost na tlak – vključno s industrijskimi tlemi, parkirnimi ploščadmi in gradnjo cest.

Več podrobnosti

XPS 300 SLOPE — Konična toplotna izolacija za odvodnjavanje ravnih streh

Slope · 300 kPa

XPS 300 SLOPE — Konična toplotna izolacija za odvodnjavanje ravnih streh

Uporabite XPS 300 SLOPE na ravnih strehah, terasah in zelenih strehah, kjer mora enoslojna rešitev zagotoviti odtočni naklon in trajno toplotno izolacijo.

Več podrobnosti
Pojdi v katalog
Kontaktirajte nas

Kontaktirajte nas

Pustite svoje kontaktne podatke in odgovorili vam bomo v najkrajšem možnem času.

Kontaktirajte nas

Pustite svoje kontaktne podatke in odgovorili vam bomo v najkrajšem možnem času.

Vaša zahteva je bila poslana

Kmalu vas bomo kontaktirali